Quilatero 1.0 recessed for outdoor applications
drive-over up to 1500 kg
recessed (wall, floor)
Power consumption: 3,5W
Power supply: 110-230Vac
Lumen output at source: 221 lm (3000K, CRI >90), 260 lm (3000K, CRI 80)
Delivered lumen output: 170 lm (3000K, CRI >90, 14°), 200 lm (3000K, CRI 80, 14°)
1 power LED, 2-step MacAdam, 60 000h L90 B10 (Ta 25°C)
LED colour: 2200K, 2700K, 3000K, 4000K
Optics: 7°, 10°: optical system consisting of a high-efficiency TIR lens combined with a high-quality technical filter, 14°, 32°, 42°, 12°x45°: optical system consisting of a high-efficiency, deep-set TIR lens combined with a high-quality technical filter, sharp 35°: SHARP optical system consisting of a deep-set plano-convex lens for an extremely well-defined light beam, diffuse: optical system consisting of a screen in frosted / transparent Plexiglas, wall washer: optical system consisting of a high-efficiency TIR lens combined with an asymmetrical technical filter
CRI Colour Rendering Index: 80, >90
Body material: body made of heat-dissipating, carbon-fibre-reinforced semicrystalline technopolymer with a thermal conductivity equal to that of stainless steel and high resistance to impact and sub-zero temperatures, and to corrosion even in harsh environments (saline). Trim in AISI 316L stainless steel, laser cut, machined and finished (version with cor-ten trim), body made of heat-dissipating, carbon-fibre-reinforced semicrystalline technopolymer with a thermal conductivity equal to that of stainless steel and high resistance to impact and sub-zero temperatures, and to corrosion even in harsh (saline) environments. Trim in AISI 316L stainless steel, laser cut, machined and finished, then micro-peened, passivated and electropolished to guarantee excellent corrosion resistance of more than 2000 hours of salt spray (version with trim in stainless steel)
Finishes: cor-ten finish obtained through an initial treatment with a ceramic nanoparticle coating, to prepare for painting, followed by a coat of epoxy paint and one of polyester paint to provide corrosion resistance of more than 2000 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector, stainless steel
RAL finish on request
Screen material: 10-mm-thick transparent extra-clear glass, high transmittance to ensure chromatic uniformity of light, serigraphed grey (RAL 7015), and tempered for excellent impact and scratch resistance, 10-mm-thick transparent extra-clear glass, high transmittance to ensure chromatic uniformity of light. Half the surface of the glass serigraphed black (RAL 9005), and edge serigraphed grey (RAL 7015); glass tempered for excellent impact and scratch resistance (version with wall-washer optics)
Seals: the silicone rubber gaskets guarantee maximum resistance to UV rays and unchanging mechanical characteristics over time
Installation: product complete with IP68 connector and built-in IPS system. Compatible with H07RN-F cable with minimum cross-section 2x1 and cable Ø min. 7 mm max. 12 mm. Simplified connection for quick, effective installation. Easy installation on the relative outer casing using mounting clip built into the lighting fixture
built-in power supply unit
Ingress protection: IP68 72h, IP66, IP69
Impact resistance: IK08
Fast installation: direct connection between fixture and mains power supply
Casambi-compatible version, controllable with the Casambi app, available on request
Protection systems: IPS (Intelligent Protection System) protects lighting fixtures from water infiltrations, which can occur if there are faulty junctions between the cables in outdoor or underwater applications. This innovation, patented by L&L, also guarantees electrical protection against polarity reversal, hot plugging, ESD and power surges, which can occur if there are faults in the electrical circuit; The PID (Protective Impedance Device) protects lighting fixtures from electrical phenomena external to the system, such as static electricity accumulation or electromagnetic interference coming from the mains power. Generally, these are events with a low energy content
Operating temperature: -20°C — +45°C
Maximum device temperature: 40°C (Ta 25°C)
Glow wire test: 960°
Photobiological safety: in accordance with IEC TR 62778:2014
Appliance class: class II
Weight: 550 g
Dimensions: 100x100x111 mm
Energy efficiency class: F (light source) in accordance with EU 2019/2015
Accessories: anti-glare screen, honeycomb louvre, WCA13 Outer casing
tested and approved via E.O.L. (End Of Line) test with functioning test and check of electrical power consumption